اعضا

1- Mohammadreza Jahangiri, Hessam Bayani, “Adding chemical composition variable to traditional time–temperature-transformation (TTT) diagrams with an experimental cost-effective method”, Materials Letters, Volume 277, 15 October 2020, 128397
2- M.R. Jahangiri, A. Bajgholi, A. Fallah, "Effect of annealing method and applied stress on aging behavior of copper-aluminum bimetals", Journal of Alloys and Compounds, Volume 816, 5 March 2020, 152676
3- H. Fazilatpanah, M.R. Jahangiri, A. Khodabandeh, "Hot deformation behavior and processing maps of iron‐nickel based superalloy”, Materialwissenschaft und Werkstofftechnik, Volume 50, Issue 11, November 2019, Pages: 1407-1417.
4- M.R. Jahangiri, "Different effects of γ′ and η phases on the physical and mechanical properties of superalloys”, Journal of Alloys and Compounds, Volume 802, 25 September 2019, Pages 535-545.
5- M. Abedini, M.R. Jahangiri, P. Karimi, “Rejuvenation of the microstructure and mechanical properties of a service-exposed IN939 superalloy by heat treatments”, Materials at High Temperatures, Volume 36, 2019 - Issue 1, Pages 19-26.
6- M. Abedini, M.R. Jahangiri, P. Karimi, “Oxidation and hot corrosion behaviors of service-exposed and heat-treated gas turbine vanes made of IN939 alloy”, Oxidation of Metals, Volume. 90, 2018, Pages 469-484.
7- M.R. Jahangiri, " The Relationship Between Hot and Cold Rolling Parameters and Secondary Recrystallization Behavior in Silicon Steel Sheets", Journal of Materials Engineering and Performance, August 2015, 24(8):3159-3168.
8- M.R. Jahangiri, H. Arabi, SMA. Boutorabi, “Comparison of microstructural stability of IN939 superalloy with two different manufacturing routes during long-time aging”, Transactions of Nonferrous Metals Society of China, Volume 24, Issue 6, June 2014, Pages 1717-1729.
9- M.R. Jahangiri, M. Abedini, “Effect of long time service exposure on microstructure and mechanical properties of gas turbine vanes made of IN939 alloy”, Materials & Design, Volume 64, December 2014, Pages 588-600.
10- MR Jahangiri, A Bajgholi, AA Zhaam, “Development of a new three-stage cold rolling manufacturing technology for grain-oriented silicon steel sheets”, The International Journal of Advanced Manufacturing Technology, Volume 75, 2014, Pages1291–1298.
11- M.R. Jahangiri, AA Fallah, A. Ghiasipour, “Cement kiln dust induced corrosion fatigue damage of gas turbine compressor blades – A failure analysis”, Materials & Design, Volume 62, October 2014, Pages 288-295.
12- M.R. Jahangiri, H. Arabi, SMA. Boutorabi, “Investigation on the dissolution of η phase in a cast Ni-based superalloy”, International Journal of Minerals, Metallurgy, and Materials, Volume 20, 2013, Pages42–48.
13- M.R. Jahangiri, H. Arabi, SMA. Boutorabi, “High-Temperature Compression Behavior of Cast and Homogenized IN939 Superalloy”, Metallurgical and Materials Transactions A, Volume 44, 2013, Pages1827–1841.
14- M.R. Jahangiri, SMA. Boutorabi, H. Arabi,” Study on incipient melting in cast Ni base IN939 superalloy during solution annealing and its effect on hot workability”, Materials Science and Technology, Volume 28, 2012 - Issue 12, Pages 1402-1413.
15- M.R. Jahangiri, M. Soltanlou, R. Gholamipour, “Optimization of Pre-Rolling Homogenizing Heat Treatment for Cast Silicon Steel Ingots”, Arabian Journal for Science and Engineering, Volume 37, 2012, Pages1065–1076.
16- M.R. Jahangiri, H. Arabi, SMA. Boutorabi, “Development of wrought precipitation strengthened IN939 superalloy”, Materials Science and Technology, Volume 28, 2012 - Issue 12, Pages 1470-1478.
17- M.R. Jahangiri, M. Nili Ahmadabadi, H. Farhangi, “Enhancement of Fatigue Properties of Ductile Irons by Successive Austempering Heat Treatment”, Journal of Materials Engineering and Performance Volume 20, 2011, Pages1642–1647.
18- M.R. Jahangiri, “Failure Analysis of Type 304 Stainless Steel Tubes in an Energy Production Plant Heat Exchangers”, J. Pressure Vessel Technology, Volume 133(6), 2011, 064503 (10 pages).
19- M.R. Jahangiri, A.A. Fallah, “Effects of welding defects on reducing lifetimes of first stage nozzles of a 123 MW gas turbine made of FSX-414 alloy”, Materials & Design, Volume 32, Issue 1, January 2011, Pages 424-432.